Archer C7 v2 невозможно подключиться

Здесь вы можете найти информацию по сервис-центрам в вашем городе, а также оставить отзыв, или жалобу на их работу

Модераторы: exclusive, al1sh

Ответить
alexradch
Сообщения: 1
Зарегистрирован: 03 сен 2018, 00:25
Страна: Россия

Archer C7 v2 невозможно подключиться

Сообщение alexradch » 03 сен 2018, 01:18

:cry: Здравствуйте.
Есть роутер Archer C7 v2, ранее на роутере стояла прошивка OpenWrt. После 2-х недельного отсутствия приехав домой обнаружил, что все устройства подключенные к LAN недоступны. При назначении статического IP устройства включенные в LAN-порты роутера видят друг-друга... Подумал проблема с прошивкой, решил откатится на родную.
По tftp не получилось прошить, нет передачи данных, при этом горит линк на портах, и на роутере и на ноутбуке. Для прошивки использую tftpd32, на ноуте IP 192.168.0.66
Скажу сразу, что на аналогичном роутере Archer C7 v4 получается перепрошиться, так что проблема не в файерволе, антиврусе и т.п.

В итоге после безуспешных попыток, зашел по WiFi и через web-интерфейс openWrt прошил стоковую прошивку (без boot). И... получил недоступность и по wiFi вдобавок.
Распаял UART, лог загрузки ниже под катом.
Похоже грузится штатно, видно в режиме восстановления ожидает ArcherC7v2_tp_recovery.bin но на tftpd никаких запросов не фиксируется...
Теперь осталась возможность залогиниться в BusyBox по UART и раскирпичить роутер... Но как ?
В ответ на посылку логина:
Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: admin
Password:
Login incorrect
U-Boot 1.1.4 (Feb 9 2017 - 11:51:45)

ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(179): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x3, 0x1f)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Flash Manuf Id 0x1, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
Vlan config...
TEST: FINAL REG VAL after TX Calibration - 0x46000000
TEST: FINAL XMII VAL after RX Calibration - 0x46000000
TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00000001
athrs17_reg_init: complete
: cfg1 0x80000000 cfg2 0x7335
eth0: ba:be:fa:ce:08:41
eth0 up
athrs17_reg_init_wan done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
eth1 up
eth0, eth1
Setting 0x18116290 to 0x58b1214f
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'ArcherC7v2_tp_recovery.bin'.
Load address: 0x80060000
Loading: T T ## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

Booting QCA955x<0>
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Thu Mar 8 10:14:28 CST 2018
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 16
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 619 ahb 206
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),14848k(rootfs),320k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112924k/131072k available (1844k kernel code, 17980k reserved, 429k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000]
[ 0.080000] ****************ALLOC***********************
[ 0.080000] Packet mem: 8026a4e0 (0xe00000 bytes)
[ 0.080000] ********************************************
[ 0.080000]
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] ath_pcibios_init: bus 0
[ 0.080000] ***** Warning PCIe 0 H/W not found !!!
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.080000] ath_pcibios_init: bus 1
[ 0.080000] ath_pcibios_init(232): PCI 1 CMD write: 0x356
[ 0.080000] registering PCI controller with io_map_base unset
[ 0.080000] ===@@@@@@@@@@@=>use GPIO23 as wifi button control!
[ 0.080000] bio: create slab <bio-0> at 0
[ 0.084000] pcibios_map_irq: IRQ 76 for bus 1
[ 0.084000] NET: Registered protocol family 2
[ 0.084000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.084000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.084000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.084000] TCP reno registered
[ 0.084000] NET: Registered protocol family 1
[ 0.084000] ATH GPIOC major 0
[ 0.084000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.084000] msgmni has been set to 220
[ 0.088000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.088000] io scheduler noop registered
[ 0.088000] io scheduler deadline registered (default)
[ 0.088000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.088000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.088000] console [ttyS0] enabled
[ 0.396000] PPP generic driver version 2.4.2
[ 0.400000] NET: Registered protocol family 24
[ 0.404000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.412000] Creating 5 MTD partitions on "ath-nor0":
[ 0.416000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.420000] 0x000000020000-0x000000120000 : "kernel"
[ 0.428000] 0x000000120000-0x000000fa0000 : "rootfs"
[ 0.432000] 0x000000fa0000-0x000000ff0000 : "config"
[ 0.436000] 0x000000ff0000-0x000001000000 : "ART"
[ 0.444000] ->Oops: flash id 0x12018 .
[ 0.448000] Ooops, why the devices couldn't been initialed?
[ 0.452000] TCP cubic registered
[ 0.456000] NET: Registered protocol family 10
[ 0.460000] NET: Registered protocol family 17
[ 0.464000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.472000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.480000] athwdt_init: Registering WDT success
[ 0.484000] ath_otp_init: Registering OTP success
[ 0.496000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.504000] Freeing unused kernel memory: 120k freed

init started: BusyBox v1.01 (2015.09.28-09:17+0000) multi-call binary
This Board use 2.6.31
[ 2.164000] xt_time: kernel timezone is -0000
[ 2.364000] nf_conntrack version 0.5.0 (2048 buckets, 81920 max)
[ 2.372000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.380000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.388000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.876000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/igmp_agent.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 3.384000] PPPoL2TP kernel driver, V1.0
[ 3.404000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

(none) mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
(none) login: [ 7.968000] Read from 0X20000 to 0X2014C: OK
[ 8.068000] Read from 0XFA0000 to 0XFB2ED4: OK
[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_0=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_1=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_2=0x00000000[ucVlanCfg_init, 175]Prepare paramter:vlanEntry_3=0x00000000[ucVlanCfg_init, 178]VLAN CFG PARAM STR:vlanEnable=0 vlanEntry_0=0 vlanEntry_1=0 vlanEntry_2=0 vlanEntry_3=0 ====>>>>vid_offset is 0
====>>>>lan:eth0[ 8.480000] Read from 0X1FC00 to 0X1FC06:.1
OK
[ 8.912000] qca955x_GMAC: Length per segment 1536
[ 8.916000] 955x_GMAC: qca955x_gmac_attach
[ 8.920000] 955x_GMAC: qca955x_set_gmac_caps
[ 8.924000] Currently in polling mode unit1
[ 8.928000] mac:1 Registering S17....
[ 8.932000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
[ 8.940000] qca955x_GMAC: Max segments per packet : 1
[ 8.944000] qca955x_GMAC: Max tx descriptor count : 220
[ 8.948000] qca955x_GMAC: Max rx descriptor count : 220
[ 8.956000] qca955x_GMAC: Mac capability flags : 12002200
[ 8.960000] 955x_GMAC: qca955x_gmac_attach
[ 8.964000] 955x_GMAC: qca955x_set_gmac_caps
[ 8.968000] Currently in polling mode unit0
[ 8.972000] mac:0 Registering S17....
[ 8.976000] qca955x_GMAC: RX TASKLET - Pkts per Intr:200
[ 8.984000] qca955x_GMAC: Max segments per packet : 1
[ 8.988000] qca955x_GMAC: Max tx descriptor count : 220
[ 8.992000] qca955x_GMAC: Max rx descriptor count : 220
[ 9.000000] qca955x_GMAC: Mac capability flags : 10002A00
[ 9.004000] 955x_GMAC: Serdes PLL is locked value 0x1f038516
[ 9.640000] athr_gmac_ring_alloc Allocated 3520 at 0x8794d000
[ 9.648000] athr_gmac_ring_alloc Allocated 3520 at 0x87b29000
[ 9.952000] 955x_GMAC: eth1 in SGMII MODE
[ 9.956000] Scorpion -----> S17 PHY
[ 9.988000] Hello, nat helper module for 1.08!
[ 9.992000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 10.000000]
[ 10.000010.420000] [VLAN_MNGR] <07> Creating VLAN VID= 7 Member=0013ddd0 Desc:IGMP Snooping
[ 10.428000] [VLAN_MNGR] <08> Creating VLAN VID= 8 Member=0013d7d0 Desc:IGMP Snoopi1175d0 Desc:IGMP Snooping
[ 10.608000] [VLAN_MNGR] <30> Creating VLAN VID= 30 Member=00115fd0 Desc:IGMP Snooping
[ 10.616000] [VLAN_MNGR] <31> Creating VLAN VID= 31 Member=00115dd0 Desc:IGMP Snooping
[ 10.624000] [VLAN_MNGR] <32> Creating VLAN VID= 32 Member=001157d0 Desc:IGMP Snooping
[ 10.632000] [VLAN_MNGR] <33> Creating VLAN VID= 33 Member=001155d0 Desc:IGMP Snooping
[ 10.640000] [VLAN_MNGR] <34> Creating VLAN VID= 34 Member=0011ffe0 Desc:Guest VLAN
[ 10.652000] athrs17_reg_init:done
[ 10.652000] 955x_SGMII::athr_gmac_sgmii_setup Done
[ 10.660000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.664000] Setting PHY...
[ 10.668000] vid_offset is 0
1 Member=00115dd0 Desc:IGMP Snooping
[ 10.624000] [VLAN_MNGR] <32> Creating VLAN VID= 32 Member=001157d0 Desc:IGMP Snooping
[ 10.632000] [VLAN_MNGR] <33> Creating VLAN VID= 33 Member=001155d0 Desc:IGMP Snooping
[ 10.640000] [VLAN_MNGR] <34> Creating VLAN VID= 34 Member=0011ffe0 Desc:Guest VLAN
[ 10.652000] athrs17_reg_init:done
[ 10.652000] 955x_SGMII::athr_gmac_sgmii_setup Done
[ 10.660000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.664000] Setting PHY...
[ 10.668000] vid_offset is 0
ooping
[ 10.484000] [VLAN_MNGR] <15> Creating VLAN VID= 15 Member=00135dd0 Desc:IGMP Snooping
[ 10.492000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP Snooping
[ 10.504000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP Snooping
[ 10.512000] [VLAN_MNGR] <18> Creating VLAN VID= 18 Member=0011ffd0 Desc:IGMP Snooping
[ 10.520000] [VLAN_MNGR] <19> Creating VLAN VID= 19 Member=0011fdd0 Desc:IGMP Snooping
[ 10.528000] [VLAN_MNGR] <20> Creating VLAN VID= 20 Member=0011f7d0 Desc:IGMP Snooping
[ 10.536000] [VLAN_MNGR] <21> Creating VLAN VID= 21 Member=0011f5d0 Desc:IGMP Snooping
[ 10.544000] [VLAN_MNGR] <22> Creating VLAN VID= 22 Member=0011dfd0 Desc:IGMP Snooping
[ 10.552000] [VLAN_MNGR] <23> Creating VLAN VID= 23 Member=0011ddd0 Desc:IGMP Snooping
[ 10.560000] [VLAN_MNGR] <24> Creating VLAN VID= 24 Member=0011d7d0 Desc:IGMP Snooping
[ 10.568000] [VLAN_MNGR] <25> Creating VLAN VID= 25 Member=0011d5d0 Desc:IGMP Snooping
[ 10.576000] [VLAN_MNGR] <26> Creating VLAN VID= 26 Member=00117fd0 Desc:IGMP Snooping
[ 10.584000] [VLAN_MNGR] <27> Creating VLAN VID= 27 Member=00117dd0 Desc:IGMP Snooping
[ 10.592000] [VLAN_MNGR] <28> Creating VLAN VID= 28 Member=001177d0 Desc:IGMP Snooping
[ 10.600000] [VLAN_MNGR] <29> Creating VLAN VID= 29 Member=00[ 11.672000] Phy setup Complete
[ 11.684000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.760000] device eth0.1 entered promiscuous mode
[ 11.776000] Read from 0X1FC00 to 0X1FC06: OK
[ 11.780000] SET INTF MAC 0:14-cc-20-5c-bf-3a
[ 11.788000] Lan UDP checksum 0 adding rule #3
[ 11.796000] ACL is not yet enabled. Enabling...
[ 11.800000] SET INTF MAC 1:14-cc-20-5c-bf-3b
[ 11.804000] ttl adding rule #0
[ 11.808000] Wan UDP checksum 0 adding rule #2
[ 11.844000] device eth0 entered promiscuous mode
[ 11.908000] br0: port 1(eth0.1) entering forwarding state
[ 13.812000] Adding ACL rules #1 - wan to lan, dst ip is lan net
[ 14.388000] nf_conntrack_rtsp v0.6.21 loading
[ 14.408000] nf_nat_rtsp v0.6.21 loading
[ 14.464000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

====>>>>init2G...right region RU,cur region:83
[ 14.692000] adf: module license 'Proprietary' taints kernel.
[ 14.700000] Disabling lock debugging due to kernel taint
[ 13.812000] Adding ACL rules #1 - wan to lan, dst ip is lan net
[ 14.388000] nf_conntrack_rtsp v0.6.21 loading
[ 14.408000] nf_nat_rtsp v0.6.21 loading
[ 14.464000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

====>>>>init2G...right region RU,cur region:83
[ 14.692000] adf: module license 'Proprietary' taints kernel.
[ 14.700000] Disabling lock debugging due to kernel taint
11.808000] Wan UDP checksum 0 adding rule #2
[ 11.844000] device eth0 entered promiscuous mode
[ 11.908000] br0: port 1(eth0.1) entering forwarding state
N VID= 15 Member=00135dd0 Desc:IGMP Snooping
[ 10.492000] [VLAN_MNGR] <16> Creating VLAN VID= 16 Member=001357d0 Desc:IGMP Snooping
[ 10.504000] [VLAN_MNGR] <17> Creating VLAN VID= 17 Member=001355d0 Desc:IGMP Snooping
[ 10.512000] [VLAN_MNGR] <18> Creating VLAN VID= 18 Member=0011ffd0 Desc:IGMP Snooping
[ 10.520000] [VLAN_MNGR] <19> Creating VLAN VID= 19 Member=0011fdd0 Desc:IGMP Snooping
[ 10.528000] [VLAN_MNGR] <20> Creating VLAN VID= 20 Member=0011f7d0 Desc:IGMP Snooping
[ 10.536000] [VLAN_MNGR] <21> Creating VLAN VID= 21 Member=0011f5d0 Desc:IGMP Snooping
[ 10.544000] [VLAN_MNGR] <22> Creating VLAN VID= 22 Member=0011dfd0 Desc:IGMP Snooping
[ 10.552000] [VLAN_MNGR] <23> Creating VLAN VID= 23 Member=0011ddd0 Desc:IGMP Snooping
[ 10.560000] [VLAN_MNGR] <24> Creating VLAN VID= 24 Member=0011d7d0 Desc:IGMP Snooping
[ 10.568000] [VLAN_MNGR] <25> Creating VLAN VID= 25 Member=0011d5d0 Desc:IGMP Snooping
[ 10.576000] [VLAN_MNGR] <26> Creating VLAN VID= 26 Member=00117fd0 Desc:IGMP Snooping
[ 10.584000] [VLAN_MNGR] <27> Creating VLAN VID= 27 Member=00117dd0 Desc:IGMP Snooping
[ 10.592000] [VLAN_MNGR] <28> Creating VLAN VID= 28 Member=001177d0 Desc:IGMP Snooping
[ 10.600000] [VLAN_MNGR] <29> Creating VLAN VID= 29 Member=00 OK
[ 10.172000] [VLAN_MNGR] Registering: VID= 0 Member=001357d0 Policy=3 cookie=87bcb6f8 desc=IGMP Snooping OK
[ 10.180000] [VLAN_MNGR] Registering: VID= 0 Member=001355d0 Policy=3 cookie=87bcb6fc desc=IGMP Snooping OK
[ 10.192000] [VLAN_MNGR] Registering: VID= 0 Member=0011ffd0 Policy=3 cookie=87bcb700 desc=IGMP Snooping OK
[ 10.200000] [VLAN_MNGR] Registering: VID= 0 Member=0011fdd0 Policy=3 cookie=87bcb704 desc=IGMP Snooping OK
[ 10.212000] [VLAN_MNGR] Registering: VID= 0 Member=0011f7d0 Policy=3 cookie=87bcb708 desc=IGMP Snooping OK
[ 10.220000] [VLAN_MNGR] Registering: VID= 0 Member=0011f5d0 Policy=3 cookie=87bcb70c desc=IGMP Snooping OK
[ 10.232000] [VLAN_MNGR] Registering: VID= 0 Member=0011dfd0 Policy=3 cookie=87bcb710 desc=IGMP Snooping OK
[ 10.240000] [VLAN_MNGR] Registering: VID= 0 Member=0011ddd0 Policy=3 cookie=87bcb714 desc=IGMP Snooping OK
[ 10.252000] [VLAN_MNGR] Registering: VID= 0 Member=0011d7d0 Policy=3 cookie=87bcb718 desc=IGMP Snooping OK
[ 10.260000] [VLAN_MNGR] Registering: VID= 0 Member=0011d5d0 Policy=3 cookie=87bcb71c desc=IGMP Snooping OK
[ 10.272000] [VLAN_MNGR] Registering: VID= 0 Member=00117fd0 Policy=3 cookie=87bcb720 desc=IGMP Snooping OK
[ 10.280000] [VLAN_MNGR] Registering: VID= 0 Member=00117dd0 Policy=3 cookie=87bcb724 desc=IGMP Snooping OK
[ 10.292000] [VLAN_MNGR] Registering: VID= 0 Member=001177d0 Policy=3 cookie=87bcb728 desc=IGMP Snooping OK
[ 10.300000] [VLAN_MNGR] Registering: VID= 0 Member=001175d0 Policy=3 cookie=87bcb72c desc=IGMP Snooping OK
[ 10.312000] [VLAN_MNGR] Registering: VID= 0 Member=00115fd0 Policy=3 cookie=87bcb730 desc=IGMP Snooping OK
[ 10.320000] [VLAN_MNGR] Registering: VID= 0 Member=00115dd0 Policy=3 cookie=87bcb734 desc=IGMP Snooping OK
[ 10.332000] [VLAN_MNGR] Registering: VID= 0 Member=001157d0 Policy=3 cookie=87bcb738 desc=IGMP Snooping OK
[ 10.340000] [VLAN_MNGR] Registering: VID= 0 Member=001155d0 Policy=3 cookie=87bcb73c desc=IGMP Snooping OK
[ 10.352000] [VLAN_MNGR] Registering: VID= 0 Member=0011ffe0 Policy=3 cookie=87bcb6c0 desc=Guest VLAN OK
[ 10.360000] [VLAN_CONFIG] vlanEnable:Disable
[ 10.364000] [VLAN_CONFIG] Aborting VLAN CONFIG!
[ 10.372000] [VLAN_MNGR] <01> Creating VLAN VID= 1 Member=001955d0 Desc:VLAN 1 For LAN
[ 10.380000] [VLAN_MNGR] <02> Creating VLAN VID= 2 Member=001bff50 Desc:VLAN 2 For WAN
[ 10.388000] [VLAN_MNGR] <03> Creating VLAN VID= 3 Member=0013fdd0 Desc:IGMP Snooping
[ 10.396000] [VLAN_MNGR] <04> Creating VLAN VID= 4 Member=0013f7d0 Desc:IGMP Snooping
[ 10.404000] [VLAN_MNGR] <05> Creating VLAN VID= 5 Member=0013f5d0 Desc:IGMP Snooping
[ 10.412000] [VLAN_MNGR] <06> Creating VLAN VID= 6 Member=0013dfd0 Desc:IGMP Snooping
[ [ 15.520000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
[ 15.604000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 15.720000] ath_dfs: Version 2.0.0
[ 15.720000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
usrconf_allocate_memory 212 shmget success id:43511 32769[ 16.164000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 16.976000] Read from 0X20000 to 0X20120: OK
[ 18.924000] ath_ahb: 10.2-00082-4 (Atheros/multi-bss)
[ 18.928000] __ath_attach: Set global_scn[0]
[ 18.944000] Enterprise mode: 0x53fc0000
[ 18.948000] Restoring Cal data from Flash
[ 18.956000] Green-AP : Green-AP : Attached
[ 18.956000]
[ 18.968000] ath_get_caps[6150] rx chainmask mismatch actual 7 sc_chainmak 0
[ 18.972000] ath_get_caps[6125] tx chainmask mismatch actual 7 sc_chainmak 0
[ 18.988000] ath_attach_dfs[12578] dfsdomain 1
[ 19.016000] SC Callback Registration for wifi0
[ 19.020000] wifi0: Atheros ???: mem=0xb8100000, irq=2
[ 19.024000] ath_pci: 10.2-00082-4 (Atheros/multi-bss)
[ 19.032000] ath_pci_probe
[ 19.032000] PCI device id is 003c :003c
[ 19.044000] ath_pci 0000:01:00.0: ath DEBUG: sc=0x86f46c00
[ 19.048000]
[ 19.048000] ol_ath_pci_configure : num_desired MSI set to 0
[ 19.056000]
[ 19.056000] Using PCI Legacy Interrupt
[ 19.872000] __ol_ath_attach: ath_attach TODO
[ 19.876000] __ol_ath_attach: dev name wifi1
[ 19.880000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[ 19.892000] OL_ACBKMinfree : 0
[ 19.896000] OL_ACBEMinfree : 0
[ 19.896000] OL_ACVIMinfree : 0
[ 19.900000] OL_ACVOMinfree : 0
[ 19.904000] ol_ath_attach() BMI inited.
[ 19.908000] ol_ath_attach() BMI Get Target Info.
[ 19.912000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
[ 19.920000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[ 19.924000] ol_ath_attach() configure Target .
[ 19.932000] qc98xx_verify_checksum: flash checksum passed: 0x9a32
[ 19.940000] ol_transfer_bin_file 1882: Download Flash data len 2116
[ 19.956000] ol_transfer_bin_file 1827: Download Firmware data len 227320
[ 20.924000] ol_ath_attach() Download FW.
[ 20.928000] ol_ath_attach() HT Create .
[ 20.932000] ol_ath_attach() HIF Claim.
[ 20.936000] ol_ath_attach() BMI Done.
[ 20.940000] ol_ath_attach() WMI attached. wmi_handle 86e20000
[ 20.948000] +HWT
[ 20.952000] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5
[ 20.960000] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x602d00 nbytes 0 recv_ctxt 0x86e14a60
[ 20.968000] -HWT
[ 20.972000] HTC Service:0x0300 ep:1 TX flow control disabled
[ 20.980000] CE_pkt_dl_len_set CE 4 Pkt download length 64
[ 20.988000] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 86ed0000
[ 20.996000] HTC Service:0x0100 ep:2 TX flow control disabled
[ 21.004000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
[ 21.012000] num_rf_chain : 00000003
[ 21.016000] ht_cap_info: : 0000085b
[ 21.020000] vht_cap_info : 338001b2
[ 21.020000] vht_supp_mcs : 0000ffea
[ 21.024000] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
[ 21.032000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 444 actual units 145
[ 21.040000] chunk 0 len 64380 requested ,ptr 0x6ee0000
[ 21.056000] FIRMWARE:P 145 V 16 T 443
[ 21.056000]
[ 21.060000] FIRMWARE:_wlan_rtt_enable
[ 21.064000] wmi_ready_event_rx: WMI UNIFIED READY event
[ 21.072000] ol_ath_connect_htc() WMI is ready
[ 21.076000] ol_ath_set_host_app_area TODO
[ 21.080000] target uses HTT version 2.1; host uses 2.1
[ 21.092000] ol_ath_attach() connect HTC.
[ 21.096000] bypasswmi : 0
[ 21.096000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[ 21.108000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
[ 21.116000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
[ 21.124000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
[ 21.128000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
[ 21.136000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
[ 21.144000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
[ 21.152000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
[ 21.160000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
[ 21.168000] Add VHT80 channel: 5210
[ 21.168000] Add VHT80 channel: 5290
[ 21.172000] Add VHT80 channel: 5530
[ 21.176000] Add VHT80 channel: 5610
[ 21.180000] Add VHT80 channel: 5690
[ 21.184000] Add VHT80 channel: 5775
[ 21.188000] Skipping VHT80 channel 5825
[ 21.192000] ol_ath_phyerr_attach: called
[ 21.196000] OL Resmgr Init-ed
[ 21.200000] Green-AP : Green-AP : Attached
[ 21.200000]
[ 21.204000] Green-AP : Attached
[ 21.208000] ol_if_dfs_setup: called
[ 21.212000] ol_if_dfs_attach: called; ptr=86ec9974, radar_info=87b21be0
[ 21.224000] ol_ath_rtt_meas_report_attach: called
[ 21.232000] ol_ath_attach() UMAC attach .
[ 21.236000] ol_if_dfs_configure: called
[ 21.240000] ol_if_dfs_configure: FCC domain
[ 21.244000] ol_if_dfs_disable: called
[ 21.248000] ol_ath_attach: Calling ol_if_dfs_configure
[ 21.252000] __ol_ath_attach: init tx/rx TODO
[ 21.256000] __ol_ath_attach: hard_header_len reservation 58
[ 21.264000] SC Callback Registration for wifi1
[ 21.448000] ath_attach_dfs[12578] dfsdomain 1
[ 21.560000] VAP device ath0 created
[ 21.640000]
[ 21.640000] DES SSID SET=TP-LINK_BF3A
[ 21.656000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
[ 21.664000] Set freq vap stop send + 86cd4000
[ 21.668000] Set freq vap stop send -86cd4000
[ 21.700000] Set wait done --86cd4000
[ 21.868000] Set freq vap stop send + 86cd4000
[ 21.872000] Set freq vap stop send -86cd4000
[ 21.904000] Set wait done --86cd4000
[ 21.932000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 )
[ 21.940000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 )
[ 21.948000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 )
[ 21.956000] FWLOG: [39036] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 )
[ 21.964000] FWLOG: [39042] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 )
[ 21.972000] FWLOG: [39042] WHAL_ERROR_RESET_PM ( )
[ 25.768000] Interference detected
[ 25.768000] rx_clear=100, rx_frame=0, tx_frame=0
[ 26.244000] Scan in progress.. Cancelling it
[ 26.880000] athr_gmac_ring_alloc Allocated 3520 at 0x86ec7000
[ 26.888000] athr_gmac_ring_alloc Allocated 3520 at 0x87b1c000
[ 27.192000] 955x_GMAC: eth0 in RGMII MODE
[ 27.196000] Scorpion -----> S17 PHY
[ 27.204000] athrs17_reg_init_wan done
[ 27.208000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 27.212000] Setting PHY...
[ 27.216000] vid_offset is 0
[ 27.220000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 27.248000] device eth1 entered promiscuous mode
[ 27.352000] device ath0 entered promiscuous mode
[ 27.356000] br1: port 2(ath0) entering forwarding state
[ 27.676000]
[ 27.676000] Enet:1 port1 up
[ 27.680000] 955x_GMAC: enet unit:1 is up...
[ 27.684000] eth1 SGMII 1000Mbps full duplex
[ 27.688000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
[ 27.692000] 955x_GMAC: qca955x_soc_gmac_set_link Done
[ 27.696000] 955x_GMAC: done cfg2 0x7215 ifctl 0x0 miictrl
[ 27.704000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.168000] ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
[ 28.176000] Scan in progress.. Cancelling it
[ 28.228000] br1: port 2(ath0) entering disabled state
[ 28.232000] DEVICE IS DOWN ifname=ath0
[ 28.240000] DEVICE IS DOWN ifname=ath0
[ 28.464000] br1: port 2(ath0) entering forwarding state
[ 29.220000] 955x_GMAC: qca955x_soc_gmac_set_mac_duplex
[ 29.224000] 955x_GMAC: qca955x_soc_gmac_set_link Done
[ 29.228000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 29.236000] br1: port 1(eth1) entering forwarding state
[ 29.596000] Scan in progress.. Cancelling it
[ 29.652000] br1: port 2(ath0) entering disabled state
[ 29.692000] br1: starting userspace STP failed, starting kernel STP
[ 29.764000] br1: topology change detected, propagating
[ 29.772000] br1: port 2(ath0) entering forwarding state
====>>>>init5G...right region RU cur region:83
[ 29.832000] isCountryCodeValid: EEPROM regdomain 0x0
[ 29.836000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
[ 29.844000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
[ 29.852000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
[ 29.856000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
[ 29.864000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
[ 29.872000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
[ 29.880000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
[ 29.888000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
[ 29.892000] Add VHT80 channel: 5210
[ 29.896000] Add VHT80 channel: 5290
[ 29.900000] Add VHT80 channel: 5775
[ 29.904000] Skipping VHT80 channel 5660
[ 29.908000] Skipping VHT80 channel 5680
[ 29.912000] Skipping VHT80 channel 5700
[ 29.916000] Skipping VHT80 channel 5825
[ 29.952000] ath_ioctl: SIOC80211IFCREATE CALLED
[ 29.956000] wmi_unified_vdev_create_send: ID = 0 VAP Addr = 14:cc:20:5c:bf:39:
[ 29.964000] Setting dscp for vap id: 0
[ 29.968000] VAP device ath1 created
[ 30.024000]
[ 30.024000] DES SSID SET=TP-LINK_BF39_5G
[ 30.036000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
[ 30.044000] Set freq vap stop send + 866a8000
[ 30.048000] OL vap_stop +
[ 30.052000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.060000] OL vap_stop -
[ 30.060000] STOPPED EVENT for vap 0 (86e20000)
[ 30.064000] Set freq vap stop send -866a8000
[ 30.096000] Set wait done --866a8000
[ 30.108000] ol_ath_desc_alloc_and_mark_for_mcast_clone: VAP Mcast to Unicast buffer allocated: 400
[ 30.116000] ol_ath_vap_set_param: VAP param is now supported param:66 value:2
[ 30.136000] Set freq vap stop send + 866a8000
[ 30.140000] OL vap_stop +
[ 30.144000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.148000] OL vap_stop -
[ 30.152000] STOPPED EVENT for vap 0 (86e20000)
[ 30.156000] Set freq vap stop send -866a8000
[ 30.188000] Set wait done --866a8000
[ 30.200000] OL vap_stop +
[ 30.204000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 30.208000] OL vap_stop -
[ 30.212000] STOPPED EVENT for vap 0 (86e20000)
[ 30.244000] wmi_unified_scan_start_send for vap 0 (86e20000)
[ 33.492000] Interference detected
[ 33.492000] rx_clear=99, rx_frame=0, tx_frame=0
[ 35.016000] OL vap_start +
[ 35.020000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 35.024000] OL vap_start -
[ 35.032000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 35.036000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 35.044000] ol_ath_wmm_update:
[ 35.044000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 35.052000] Notification to UMAC VAP layer
[ 35.264000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.268000] STOPPED EVENT for vap 0 (86e20000)
[ 35.528000] Interference detected
[ 35.528000] rx_clear=99, rx_frame=0, tx_frame=0
[ 35.752000] OL vap_stop +
[ 35.756000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.760000] OL vap_stop -
[ 35.764000] STOPPED EVENT for vap 0 (86e20000)
[ 35.796000] OL vap_start +
[ 35.800000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 35.804000] OL vap_start -
[ 35.808000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 35.812000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 35.820000] ol_ath_wmm_update:
[ 35.820000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 35.828000] Notification to UMAC VAP layer
[ 35.956000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.960000] STOPPED EVENT for vap 0 (86e20000)
[ 35.976000] OL vap_stop +
[ 35.980000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 35.984000] OL vap_stop -
[ 35.988000] STOPPED EVENT for vap 0 (86e20000)
[ 36.020000] OL vap_start +
[ 36.020000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 36.028000] OL vap_start -
[ 36.032000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 36.036000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 36.044000] ol_ath_wmm_update:
[ 36.044000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 36.052000] Notification to UMAC VAP layer
[ 36.068000] device ath1 entered promiscuous mode
[ 36.072000] br1: topology change detected, propagating
[ 36.076000] br1: port 3(ath1) entering forwarding state
[ 36.104000] ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1
[ 36.116000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 36.120000] STOPPED EVENT for vap 0 (86e20000)
[ 36.128000] br1: port 3(ath1) entering disabled state
[ 36.132000] DEVICE IS DOWN ifname=ath1
[ 36.136000] DEVICE IS DOWN ifname=ath1
[ 36.304000] OL vap_stop +
[ 36.304000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 36.312000] OL vap_stop -
[ 36.312000] STOPPED EVENT for vap 0 (86e20000)
[ 36.348000] OL vap_start +
[ 36.352000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 36.356000] OL vap_start -
[ 36.360000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 36.364000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 36.372000] ol_ath_wmm_update:
[ 36.372000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 36.380000] Notification to UMAC VAP layer
[ 36.384000] br1: topology change detected, propagating
[ 36.388000] br1: port 3(ath1) entering forwarding state
[ 36.556000] Interference detected
[ 36.556000] rx_clear=100, rx_frame=0, tx_frame=0
[ 36.824000] FWLOG: [54384] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xd470, 0x200008a, 0x0, 0x60 )
[ 36.832000] FWLOG: [54767] WAL_DBGID_SECURITY_ENCR_EN ( )
[ 36.836000] FWLOG: [54767] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
[ 36.844000] FWLOG: [54954] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xd6aa, 0x200008a, 0x0, 0x61 )
[ 38.128000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 38.132000] STOPPED EVENT for vap 0 (86e20000)
[ 38.140000] br1: port 3(ath1) entering disabled state
[ 38.188000] OL vap_stop +
[ 38.192000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 38.196000] OL vap_stop -
[ 38.200000] STOPPED EVENT for vap 0 (86e20000)
[ 38.232000] OL vap_start +
[ 38.236000] wmi_unified_vdev_start_send for vap 0 (86e20000)
[ 38.240000] OL vap_start -
[ 38.244000] ol_vdev_start_resp_ev for vap 0 (86e20000)
[ 38.248000] Interference detected
[ 38.248000] rx_clear=100, rx_frame=0, tx_frame=0
[ 38.256000] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 38.264000] ol_ath_wmm_update:
[ 38.264000] wmi_unified_vdev_up_send for vap 0 (86e20000)
[ 38.272000] Notification to UMAC VAP layer
[ 38.288000] br1: topology change detected, propagating
[ 38.292000] br1: port 3(ath1) entering forwarding state
[ 38.392000] port is 21, val is off
[ 38.396000] set port 21 off
[ 38.408000] port is 22, val is off
[ 38.412000] set port 22 off
[ 39.296000] Interference detected
[ 39.296000] rx_clear=99, rx_frame=0, tx_frame=0
[ 39.428000] port is 21, val is on
[ 39.432000] set port 21 on
[ 39.444000] port is 22, val is on
[ 39.448000] set port 22 on
[ 39.872000] fuse init (API version 7.12)
[ 40.104000] usbcore: registered new interface driver usbfs
[ 40.108000] usbcore: registered new interface driver hub
[ 40.116000] usbcore: registered new device driver usb
[ 40.152000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 40.156000] Port Status 1c000004
[ 40.160000] ath-ehci ath-ehci.0: ATH EHCI
[ 40.164000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 40.172000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.180000] ehci_reset Port Status 1c000000
[ 40.184000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 40.192000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.200000] ehci_reset Port Status 1c000000
[ 40.216000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 40.220000] usb usb1: configuration #1 chosen from 1 choice
[ 40.224000] hub 1-0:1.0: USB hub found
[ 40.228000] hub 1-0:1.0: 1 port detected
[ 40.236000] Port Status 1c000000
[ 40.236000] ath-ehci1 ath-ehci1.1: ATH EHCI
[ 40.240000] ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2
[ 40.252000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.256000] ehci_reset Port Status 1c000000
[ 40.260000] ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000
[ 40.268000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 40.276000] ehci_reset Port Status 1c000000
[ 40.292000] ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00
[ 40.296000] usb usb2: configuration #1 chosen from 1 choice
[ 40.304000] hub 2-0:1.0: USB hub found
[ 40.304000] hub 2-0:1.0: 1 port detected
[ 40.324000] Interference detected
[ 40.324000] rx_clear=100, rx_frame=0, tx_frame=0
[ 40.572000] SCSI subsystem initialized
[ 40.896000] Initializing USB Mass Storage driver...
[ 40.904000] usbcore: registered new interface driver usb-storage
[ 40.908000] USB Mass Storage support registered.
[ 41.008000] kcg 333 :GPL NetUSB up!
[ 41.296000] kc 90 : run_telnetDBGDServer start
[ 41.300000] kc 227 : init_DebugD end
[ 41.304000] INFO17E0: NetUSB 1.02.65.5, 0002061F : Apr 21 2015 15:30:36
[ 41.312000] INFO17E2: 7437: Archer C7 v2 :Archer C7 v2
[ 41.316000] INFO17E3: AUTH ISOC
[ 41.320000] INFO17E4: filterAudio
[ 41.324000] usbcore: registered new interface driver KC NetUSB General Driver
[ 41.332000] INFO0145: init proc : PAGE_SIZE 4096
[ 41.340000] INFO16D4: infomap 85c4be3c
[ 41.344000] INFO16D7: sleep to wait br0 to wake up
[ 41.348000] INFO15A7: tcpConnector() started... : br0
[ 41.824000] IPv6 over IPv4 tunneling driver
[ 42.256000] Interference detected
[ 42.256000] rx_clear=100, rx_frame=0, tx_frame=0
[ 43.284000] Interference detected
[ 43.284000] rx_clear=100, rx_frame=0, tx_frame=0
[ 43.988000] br1: port 2(ath0) entering disabled state
[ 44.044000] wmi_unified_vdev_stop_send for vap 0 (86e20000)
[ 44.052000] STOPPED EVENT for vap 0 (86e20000)
[ 44.188000] br1: port 3(ath1) entering disabled state
[ 44.380000] INFO155A: Bind to br0
check success
Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: admin
Password:
Login incorrect

Archer C7 mips #1 Thu Mar 8 10:14:28 CST 2018 (none)
Archer C7 login: Admin
login: no valid shadow password
Подскажите что можно попробовать еще?

Ответить

Вернуться в «Сервисные центры»