После прошивки Beta версии роутер превратился в кирпич.

AC750 Двухдиапазонный беспроводной маршрутизатор
Mikhail.Medvedev
Сообщения: 1
Зарегистрирован: 26 фев 2017, 00:17

После прошивки Beta версии роутер превратился в кирпич.

Сообщение Mikhail.Medvedev » 10 май 2017, 14:47

Название темы: После прошивки Beta версии роутер превратился в кирпич.
Аппаратная версия устройства: v1.0
Описание проблемы: Добрый день. Попробывал прошить в роутер Beta прошивку (февральскую) и он превратился в кирпич. Веб интерфейс не загружается, интернет не раздает, при загрузке мигает только usb led, через некоторое время перестает. (Он также перестает мигать если вытянуть все rj-45 кабели, оставив при этом подключенный usb). При попытке сбросить через reset ничего не происходит. Как мне быть в этой ситуации?

NeonClub
Сообщения: 10
Зарегистрирован: 21 июл 2017, 13:06
Страна: Latvian

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение NeonClub » 24 июл 2017, 16:37

Походу у вас отпечатка . не 512кб вырезать , а 512Баит )
Вроде завелся , сеть появилась тоже ! посмотрим как дальше будет ,
судя по логу он сам восстановил конфиги на сеть .. единственное вифи не пашет ...

U-Boot 1.1.3 (Aug 26 2015 - 18:00:56)

Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
------------------
Archer C20 v1.0.0
------------------
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64BF
============================================
Ralink UBoot Version: 4.1.2.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Aug 26 2015 Time:18:00:56
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes

continue to starting system. 0
disableEthForward(1158):disable switch forward...

3: System Boot system code via Flash.(0xbc020000)
do_bootm:argc=2, addr=0xbc020000
## Booting image at bc020000 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...

?----fff--~--~fx---?-?-f----f----f-f---Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #79 Fri Mar 18 12:49:30 CST 2016

The CPU feqenuce set to 580 MHz

MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=000517ce
Readback ErrCtl register=000517ce
Memory: 61360k/65536k available (2713k kernel code, 4176k reserved, 563k data, 164k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80321f68, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 5ab11d
RALINK_GPIOMODE = 58b11d
PPLL_CFG1=0xe68000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
msgmni has been set to 119
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
loop: module loaded
deice id : c8 40 17 c8 40 (4017c840)
GD25Q64C(c8 4017c840) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
spiflash_ioctl_read, Read from 0x00020000 length 0x1d0, ret 0, retlen 0x1d0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007c0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x0000007c0000-0x0000007d0000 : "config"
0x0000007d0000-0x0000007e0000 : "romfile"
0x0000007e0000-0x0000007f0000 : "rom"
0x0000007f0000-0x000000800000 : "radio"
Register flash device:flash0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2874 buckets, 11496 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 164k freed
starting pid 173, tty '': '/etc/init.d/rcS'
rdm_major = 253
SCSI subsystem initialized
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x7DF100) ffffffff-ffffffff-ffffffff-ffffffff-ffffffff-ffffffff
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288002
Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500!
spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
Read MAC from flash(0x7DF100) ffffffff-ffffffff-ffffffff-ffffffff-ffffffff-ffffffff
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288002
PROC INIT OK!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
tp_domain init ok
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0

Please press Enter to activate this console. [ util_execSystem ] 135: ipt_init cmd is "/var/tmp/dconf/rc.router"

[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
spiflash_ioctl_read, Read from 0x007c0000 length 0x10000, ret 0, retlen 0x10000
[ oal_sys_readCfgFlash ] 689: User config length is too long - ffffffff

[ dm_loadCfg ] 2278: Read config from flash failed. ret = 1
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/default_config.xml!, about to open file /etc/default_config.xml
[ parseConfigNode ] 522: Meet unrecognized object node "PhDDNSCfg", skip the node
[ parseConfigNode ] 527: Meet unrecognized parameter node "PhDDNSCfg", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "SnmpCfg", skip the node
[ parspiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
seConfigNspiflash_ioctl_read, Read from 0x007df200 length 0x4, ret 0, retlen 0x4
ode ] spiflash_ioctl_read, Read from 0x007df300 length 0x4, ret 0, retlen 0x4
522: Meetspiflash_ioctl_read, Read from 0x00020000 length 0x1d0, ret 0, retlen 0x1d0
unrecospiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
gnized object node "ACL", skip the node
[ parseConfigNode ] 527: Meet unrecognized parameter node "ACL", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "QueueManagement", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "X_TP_IPTV", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "VoiceService", skip the node
[ parseConfigNode ] 527: Meet unrecognized parameter node "VoiceService", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "X_TP_SpeedDialCfg", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "X_TP_MultiIspDialPlan", skip the node
[ parseConfigNode ] 522: Meet unrecognized object node "X_TP_CallLogCfg", skip the node
[ rsl_checkValidZoneId ] 559: Invalid zoneId.

sendto: No such file or directory
pid 251 send 2001 error
[ util_execSystem ] 135: oal_startDynDns cmd is "dyndns /var/tmp/dconf/dyndns.conf"

[ oal_sys_getOldTZInfo ] 336: Open TZ file error!
[ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135: oal_startNoipDns cmd is "noipdns /var/tmp/dconf/noipdns.conf"

[ util_execSystem ] 135: oal_startCmxDns cmd is "cmxdns /var/tmp/dconf/cmxdns.conf"

ioctl: No such device
[ util_execSystem ] 135: oal_br_addBridge cmd is "brctl spiflash_ioctl_read, Read from 0x007df100 length 0x6, ret 0, retlen 0x6
addbr br0;brctl setfd br0 0;brctl stp br0 off"

[ util_execSystem ] 135: oal_ipt_addLanRules cmd is "iptables -t filter -A INPUT -i br+ -j ACCEPT
"

[ util_execSystem ] 135: oal_intf_setIntf cmd is "ifconfig br0 192.168.0.1 netmask 255.255.255.0 up"

[ util_execSystem ] 135: oal_util_setProcLanAddr cmd is "echo "br0 16820416," > /proc/net/coRaeth v3.0 (nnWorkqueuetr)
act_Local
phy_tx_ring = 0x030dc000, tx_ring = 0xa30dc000

phy_rx_ring0 = 0x030dd000, rx_ring0 = 0xa30dd000
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288002
AdESW: Link Status Changed - Port2 Link Down
drCDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000


[ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0 up"

[ rsl_getUnusedVlan ] 1002: GET UNUSED VLAN TAG 1 : [3]
[ rsl_getUnusedVlan ] 1002: GET UNUSED VLAN TAG 2 : [4]
[ rsl_getUnusedVlan ] 1002: GET UNUSED VLAN TAG 3 : [5]
[ rsl_getUnusedVlan ] 1002: GET UNUSED VLAN TAG 4 : [6]
[ util_execSystem ] 135: oal_addVlanTagIntf cmd is "vconfig add eth0 3"

[ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0.3 up"

set if eth0.3 to *not wan dev
[ util_execSystem ] 135: oal_addVlanTagIntf cmd is "vconfig add eth0 4"

[ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0.4 up"

set if eth0.4 to *not wan dev
[ util_execSystem ] 135: oal_addVlanTagIntf cmd is "vconfig add eth0 5"

[ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0.5 up"

set if eth0.5 to *not wan dev
[ util_execSystem ] 135: oal_addVlanTagIntf cmd is "vconfig add eth0 6"

[ util_execSystem ] 135: oal_intf_enableIntf cmd is "ifconfig eth0.6 up"

set if eth0.6 to *not wan dev
[ util_execSystem ] 135: oal_addVlanTagIntf cmd is "vconfig add eth0 2"

[ util_execSystemdevice eth0.3 entered promiscuous mode
]device eth0 entered promiscuous mode
13br0: port 1(eth0.3) entering forwarding state
5:br0: port 1(eth0.3) entering forwarding state
oal_intf_enableIntf cmd is "ifconfig eth0.2 up"

set if eth0.2 to wan device eth0.4 entered promiscuous mode
devbr0: port 2(eth0.4) entering forwarding state

br0: port 2(eth0.4) entering forwarding state
[ vlan_addLanPortsIntoBridge ] 500: add lan Port 255 from br0
[ util_execdevice eth0.5 entered promiscuous mode
Sysbr0: port 3(eth0.5) entering forwarding state
tebr0: port 3(eth0.5) entering forwarding state
m ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 eth0.3"

[ utdevice eth0.6 entered promiscuous mode
il_br0: port 4(eth0.6) entering forwarding state
exbr0: port 4(eth0.6) entering forwarding state
ecSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 eth0.4"

[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 eth0.5"

[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 eth0.6"

[ util_execSystem ] 135: rsl_initIPv6CfgObj cmd is "echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6"

[ util_execSystem ] 135: oal_eth_setIGMPSnoopParam cmd is "brctl setbrsnooping br0 1"

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_RU.dat /var/Wireless/RT2860AP/SingleSKU.dat"

[ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "iwpriv ra0 set CountryRegion=1"

ra0 no private ioctls.

[ util_execSystem ] 135: oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko"

ADDRCONF(NETDEV_CHANGE): eth0.4: link becomes ready
ADDRCONF(NETDEV_CHANGE): eth0.5: link becomes ready
ADDRCONF(NETDEV_CHANGE): eth0.6: link becomes ready
ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
rt2860v2_ap: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint


=== pAd = c09d6000, size = 968080 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6_edcca_monitor_20131227
[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ util_execSystem ] 135: oal_wlan_ra_initWlan RX DESC a31d1000 size = 4096
cmd is "ifconfig ra0 up"

RTMP_TimerListAdd: add timer obj c0a83930!
RTMP_TimerListAdd: add timer obj c0a3b940!
RTMP_TimerListAdd: add timer obj c0a3e194!
RTMP_TimerListAdd: add timer obj c0a3e254!
RTMP_TimerListAdd: add timer obj c0a3e314!
RTMP_TimerListAdd: add timer obj c0a3e3d4!
RTMP_TimerListAdd: add timer obj c0a3e494!
RTMP_TimerListAdd: add timer obj c0a3e554!
RTMP_TimerListAdd: add timer obj c0a3e614!
RTMP_TimerListAdd: add timer obj c0a3e6d4!
RTMP_TimerListAdd: add timer obj c0a3e794!
RTMP_TimerListAdd: add timer obj c0a3e854!
RTMP_TimerListAdd: add timer obj c0a3e914!
RTMP_TimerListAdd: add timer obj c0a3e9d4!
RTMP_TimerListAdd: add timer obj c0a3ea94!
RTMP_TimerListAdd: add timer obj c0a3eb54!
RTMP_TimerListAdd: add timer obj c0a3ec14!
RTMP_TimerListAdd: add timer obj c0a3ecd4!
RTMP_TimerListAdd: add timer obj c0a3b914!
RTMP_TimerListAdd: add timer obj c0a3e168!
RTMP_TimerListAdd: add timer obj c0a3e228!
RTMP_TimerListAdd: add timer obj c0a3e2e8!
RTMP_TimerListAdd: add timer obj c0a3e3a8!
RTMP_TimerListAdd: add timer obj c0a3e468!
RTMP_TimerListAdd: add timer obj c0a3e528!
RTMP_TimerListAdd: add timer obj c0a3e5e8!
RTMP_TimerListAdd: add timer obj c0a3e6a8!
RTMP_TimerListAdd: add timer obj c0a3e768!
RTMP_TimerListAdd: add timer obj c0a3e828!
RTMP_TimerListAdd: add timer obj c0a3e8e8!
RTMP_TimerListAdd: add timer obj c0a3e9a8!
RTMP_TimerListAdd: add timer obj c0a3ea68!
RTMP_TimerListAdd: add timer obj c0a3eb28!
RTMP_TimerListAdd: add timer obj c0a3ebe8!
RTMP_TimerListAdd: add timer obj c0a3eca8!
RTMP_TimerListAdd: add timer obj c0a3b8e8!
RTMP_TimerListAdd: add timer obj c0a3e1c0!
RTMP_TimerListAdd: add timer obj c0a3e280!
RTMP_TimerListAdd: add timer obj c0a3e340!
RTMP_TimerListAdd: add timer obj c0a3e400!
RTMP_TimerListAdd: add timer obj c0a3e4c0!
RTMP_TimerListAdd: add timer obj c0a3e580!
RTMP_TimerListAdd: add timer obj c0a3e640!
RTMP_TimerListAdd: add timer obj c0a3e700!
RTMP_TimerListAdd: add timer obj c0a3e7c0!
RTMP_TimerListAdd: add timer obj c0a3e880!
RTMP_TimerListAdd: add timer obj c0a3e940!
RTMP_TimerListAdd: add timer obj c0a3ea00!
RTMP_TimerListAdd: add timer obj c0a3eac0!
RTMP_TimerListAdd: add timer obj c0a3eb80!
RTMP_TimerListAdd: add timer obj c0a3ec40!
RTMP_TimerListAdd: add timer obj c0a3ed00!
RTMP_TimerListAdd: add timer obj c09e29b0!
RTMP_TimerListAdd: add timer obj c09e25a4!
RTMP_TimerListAdd: add timer obj c09e2980!
RTMP_TimerListAdd: add timer obj c09e2d28!
RTMP_TimerListAdd: add timer obj c09e2a78!
RTMP_TimerListAdd: add timer obj c09e2aa8!
RTMP_TimerListAdd: add timer obj c09e2c68!
RTMP_TimerListAdd: add timer obj c09e2c98!
RTMP_TimerListAdd: add timer obj c09e5be8!
RTMP_TimerListAdd: add timer obj c09e57dc!
RTMP_TimerListAdd: add timer obj c09e5bb8!
RTMP_TimerListAdd: add timer obj c09e5f60!
RTMP_TimerListAdd: add timer obj c09e5cb0!
RTMP_TimerListAdd: add timer obj c09e5ce0!
RTMP_TimerListAdd: add timer obj c09e5ea0!
RTMP_TimerListAdd: add timer obj c09e5ed0!
RTMP_TimerListAdd: add timer obj c09e8e20!
RTMP_TimerListAdd: add timer obj c09e8a14!
RTMP_TimerListAdd: add timer obj c09e8df0!
RTMP_TimerListAdd: add timer obj c09e9198!
RTMP_TimerListAdd: add timer obj c09e8ee8!
RTMP_TimerListAdd: add timer obj c09e8f18!
RTMP_TimerListAdd: add timer obj c09e90d8!
RTMP_TimerListAdd: add timer obj c09e9108!
RTMP_TimerListAdd: add timer obj c09ec058!
RTMP_TimerListAdd: add timer obj c09ebc4c!
RTMP_TimerListAdd: add timer obj c09ec028!
RTMP_TimerListAdd: add timer obj c09ec3d0!
RTMP_TimerListAdd: add timer obj c09ec120!
RTMP_TimerListAdd: add timer obj c09ec150!
RTMP_TimerListAdd: add timer obj c09ec310!
RTMP_TimerListAdd: add timer obj c09ec340!
RTMP_TimerListAdd: add timer obj c09ef290!
RTMP_TimerListAdd: add timer obj c09eee84!
RTMP_TimerListAdd: add timer obj c09ef260!
RTMP_TimerListAdd: add timer obj c09ef608!
RTMP_TimerListAdd: add timer obj c09ef358!
RTMP_TimerListAdd: add timer obj c09ef388!
RTMP_TimerListAdd: add timer obj c09ef548!
RTMP_TimerListAdd: add timer obj c09ef578!
RTMP_TimerListAdd: add timer obj c09f24c8!
RTMP_TimerListAdd: add timer obj c09f20bc!
RTMP_TimerListAdd: add timer obj c09f2498!
RTMP_TimerListAdd: add timer obj c09f2840!
RTMP_TimerListAdd: add timer obj c09f2590!
RTMP_TimerListAdd: add timer obj c09f25c0!
RTMP_TimerListAdd: add timer obj c09f2780!
RTMP_TimerListAdd: add timer obj c09f27b0!
RTMP_TimerListAdd: add timer obj c09f5700!
RTMP_TimerListAdd: add timer obj c09f52f4!
RTMP_TimerListAdd: add timer obj c09f56d0!
RTMP_TimerListAdd: add timer obj c09f5a78!
RTMP_TimerListAdd: add timer obj c09f57c8!
RTMP_TimerListAdd: add timer obj c09f57f8!
RTMP_TimerListAdd: add timer obj c09f59b8!
RTMP_TimerListAdd: add timer obj c09f59e8!
RTMP_TimerListAdd: add timer obj c09f8938!
RTMP_TimerListAdd: add timer obj c09f852c!
RTMP_TimerListAdd: add timer obj c09f8908!
RTMP_TimerListAdd: add timer obj c09f8cb0!
RTMP_TimerListAdd: add timer obj c09f8a00!
RTMP_TimerListAdd: add timer obj c09f8a30!
RTMP_TimerListAdd: add timer obj c09f8bf0!
RTMP_TimerListAdd: add timer obj c09f8c20!
RTMP_TimerListAdd: add timer obj c0a3dd4c!
RTMP_TimerListAdd: add timer obj c0a3d940!
RTMP_TimerListAdd: add timer obj c0a3dd1c!
RTMP_TimerListAdd: add timer obj c0a3e0c4!
RTMP_TimerListAdd: add timer obj c0a3de14!
RTMP_TimerListAdd: add timer obj c0a3de44!
RTMP_TimerListAdd: add timer obj c0a3dd7c!
RTMP_TimerListAdd: add timer obj c0a3ddac!
RTMP_TimerListAdd: add timer obj c0a3dddc!
RTMP_TimerListAdd: add timer obj c0a5a29c!
RTMP_TimerListAdd: add timer obj c0a5a3b8!
RTMP_TimerListAdd: add timer obj c0a5a2c8!
RTMP_TimerListAdd: add timer obj c0a3fe84!
RTMP_TimerListAdd: add timer obj c09dfe70!
RTMP_TimerListAdd: add timer obj c09e30a8!
RTMP_TimerListAdd: add timer obj c09e62e0!
RTMP_TimerListAdd: add timer obj c09e9518!
RTMP_TimerListAdd: add timer obj c09ec750!
RTMP_TimerListAdd: add timer obj c09ef988!
RTMP_TimerListAdd: add timer obj c09f2bc0!
RTMP_TimerListAdd: add timer obj c09f5df8!
RTMP_TimerListAdd: add timer obj c0a3fb94!
!!! use RTMP_RBUS_SUPPORT: AP_PROFILE_PATH_RBUS is /var/Wireless/RT2860AP/RT2860AP.dat
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
exec!
spiflash_ioctl_read, Read from 0x007f0000 length 0x200, ret 0, retlen 0x200
eeFlashId = 0xffff!
!! default cal bin is /etc/MT7620_AP_2T2R-4L_V15.BIN
--> rtmp_ee_flash_reset copy /etc/MT7620_AP_2T2R-4L_V15.BIN to eeprom buffer
write cal to mem only!!
The EEPROM in Flash is wrong, use default
eeFlashId = 0x7620!
E2PROM: D0 target power=0xff1e
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c09dfa68!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -2, D2 = 14, CalCode = 37 !!!
RT6352_Temperature_Init : BBPR49 = 0xfffffffe
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff4
Current Temperature from BBP_R49=0xfffffff6
RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -25 -12
- 0 - 12 28 127 127 127 127 127, offset=-12, tuning=0
RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -37 -24 - -12 - 0 16 115 115 115 115 115, offset=-12, tuning=0
mp_temperature=0xfffffffc, step = +0
E2PROM: G Tssi[-7 .. +7] = -128 -128 -128 -128 -128 -37 -24 - -12 - 0 16 115 115 115 115 115, offset=-12, tuning=0
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
ESW: Link Status Changed - Port2 Link UP
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 1, phase=3e)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= d, phase=3d)
TX IQ Calibration Done!
Change as Normal Mode(0x48b71d)
After Change, now GPIO_MODE value is 0x48b71d
RT6352_Init_ExtPA_ExtLNA: Enable Ext-LNA.
RT6352_Init_ExtPA_ExtLNA: Init Ext-LNA BBP.
bAutoTxAgcG = 0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c0a4019c!
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = ff:ff:ff:ff:ff:ff
<==== rt28xx_init, Status=0
0x1300 = 00064300
[ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_24G"

[ util_execSystem ]device ra0 entered promiscuous mode
1device ra0 left promiscuous mode
35: oal_br_addIntfIntoBridge cmd is "brctl addif br0 ra0"

brctl: bridge br0device apcli0 entered promiscuous mode
: device apcli0 left promiscuous mode
Invalid argument
[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brdevice apcli0 entered promiscuous mode
ctdevice apcli0 left promiscuous mode
l addif br0 apcli0"

brctl: bridge br0: Invalid argument
[ util_execSystem ]device ra1 entered promiscuous mode
1device ra1 left promiscuous mode
35: oal_br_addIntfIntoBridge cmd is "brctl addif br0 apcli0"

brctl: bridge br0: Invalid spiflash_ioctl_read, Read from 0x007f0000 length 0x2, ret 0, retlen 0x2
argument
[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 ra1"

brctl: bridge br0: Invalid argument
[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "wlNetlinkTool &"

DUT is Not Caled. Wireless Lan should not be used.
[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "iwpriv ra0 set ATE=ATESTART"

RTMP_TimerListAdd: add timer obj c0ac1ea8!
WLAN-Start wlNetlinkTool
Waiting for Wireless Events from interfaces...
swWlanChkAhbErr: netlink to do
[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "ated_tp &"

[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "echo 0 > /proc/tplink/led_wlan_24G"

[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "echo 0 > /proc/tplink/led_wlan_5G"

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "cp /etc/SingleSKU_5G_RU.dat /var/Wireless/RT2860AP/SingleSKU_5G.dat"

wireless tool : ated_tp open SUCC
[ util_execSystem ] 135: oal_wlan_ra_setCountryRegion cmd is "iwpriv rai0 set CountryRegionABand=9"

rai0 no private ioctls.

[ util_execSystem ] 135: oal_wlan_ra_loadDriver cmd is "insmod /lib/modules/kmdir/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko"



=== pAd = c0f82000, size = 1378784 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7650
spiflash_ioctl_read, Read from 0x007f8000 length 0x200, ret 0, retlen 0x200
eeFlashId = 0xffff!

eeprom is wrong!!
write cal to mem!
The EEPROM in Flash is wrong, use default
eeFlashId = 0x7610!
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MACVersion = 0x76502000
[ rsl_checkValidZoneId ] 559: Invalid zoneId.

[ util_execSystem ] 135: oal_wlan_ra_inMAC[Ver:Rev=0x76502000 : 0x76100002]
itWlan cmd is "ifconfig rai0 up"

load fw spent 12ms
RX DESC a207b000 size = 4096
RX1 DESC a207c000 size = 4096
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
1. Phy Mode = 49
2. Phy Mode = 49
ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
ext_pa_current_setting = 1
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
bAutoTxAgcG = 0
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [0] ,RXBackup [0]
RX Cal =0 , use RXBackup [0] to restore!!
result [0]!!
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = ff:ff:ff:ff:ff:fe
<==== rt28xx_init, Status=0
MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [0] ,RXBackup [0]
RX Cal =0 , use RXBackup [0] to restore!!
result [0]!!
FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [0]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 52, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 52, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 56, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 56, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 60, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 60, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 64, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 64, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 100, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 100, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 104, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 104, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 108, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 108, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 112, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 112, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 116, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 116, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 132, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 132, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 136, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 136, param = 0x801, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 140, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 140, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 149, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 149, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 153, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 153, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 157, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 157, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 161, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 161, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
MT76x0_Calibration - Channel = 165, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 165, param = 0x901, bSave = 0, CalibrationMode = 255
==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
MT76x0_ChipSwitchChannel: DefaultTargetPwr = 0x1c 28
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0
FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255
==== 2C70 [4] ,RXBackup [4]
2C70 [4] not 0 , backup [4]
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
[ util_execSystem ] 135: oal_wlan_ra_initWlan cmd is "echo 1 > /proc/tplink/led_wlan_5G"

[ util_execSystem ] 1device rai0 entered promiscuous mode
35device rai0 left promiscuous mode
: oal_br_addIntfIntoBridge cmd is "brctl addif br0 rai0"

brctl: bridge brdevice apclii0 entered promiscuous mode
0:device apclii0 left promiscuous mode
Invalid argument
[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "bdevice apclii0 entered promiscuous mode
rcdevice apclii0 left promiscuous mode
tl addif br0 apclii0"

brctl: bridge br0: Invalid argument
[ util_execSystdevice rai1 entered promiscuous mode
emdevice rai1 left promiscuous mode
] 135: oal_br_addIntfIntoBridge cmd is "brctspiflash_ioctl_read, Read from 0x007f8000 length 0x2, ret 0, retlen 0x2
l addif br0 apclii0"

brctl: bridge br0: Invalid argument
[ util_execSystem ] 135: oal_br_addIntfIntoBridge cmd is "brctl addif br0 rai1"

brctl: bridge br0: Invalid argument
wlNetlinkTool is already there.
DUT is Not Caled. Wireless Lan should not be used.
[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "iwpriv rai0 set ATE=ATESTART"

==== 2C70 [0] ,RXBackup [4]
RX Cal =0 , use RXBackup [4] to restore!!
result [4]!!
[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "ated_tp &"

[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "echo 0 > /proc/tplink/led_wlan_24G"

[ util_execSystem ] 135: oal_wlan_ra_initEnd cmd is "echo 0 > /proc/tplink/led_wlan_5G"

wireless tool : ated_tp open SUCC
sendto: No such file or directory
pid 251 send 2030 error
sendto: No such file or directory
pid 251 send 2004 error
[ util_execSystem ] 135: oal_startDhcps cmd is "dhcpd /var/tmp/dconf/udhcpd.conf"

[ util_execSystem ] 135: oal_lan6_startDhcp6s cmd is "dhcp6s -c /var/tmp/dconf/dhcp6s_br0.conf -P /var/run/dhcp6s_br0.pid br0 &"

[ util_execSystem ] 135: oal_lan6_startRadvd cmd is "radvd -C /var/tmp/dconf/radvd_br0.conf -p /var/run/radvd_br0.pid &"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_br_delIntfFromBridge cmd is "brctl delif br0 eth0.2"

mldProxy# file: src/mld_ifinfo.c;line: 102; error = No such file or directory
mldProxy# Err: get LLA failed
brctl: bridge br0: Invalid argument
[ wan_conn_wanPppConn_checkParamValid_v4 ] 2019: Invalid MACAddress(FF:FF:FF:00:00:00)!
[ wan_conn_wanPppConn_handleAddOpt ] 148: Invalid Ipv4 param, ret = 5902
[ rsl_setObj ] 1052: perror:5902
[ rsl_initWanUsb3gLinkCfgObj ] 740: Set WAN_PPP_CONN_OBJ failed!
[ wan_conn_wanIpConn_checkParamValid_v4 ] 1768: Invalid MACAddress(FF:FF:FF:00:00:00)!
[ rsl_initWanIpConnObj ] 695: Invalid Ipv4 parameter, ret = 5704
radvd starting
[Jan 01 03:00:17] radvd: no linklocal address configured for br0
[Jan 01 03:00:17] radvd: error parsing or activating the config file: /var/tmp/dconf/radvd_br0.conf
[ util_execSystem ] 135: prepareDropbear cmd is "dropbearkey -t rsa -f /var/tmp/dropbear/dropbear_rsa_host_key"

Will output 1024 bit rsa secret key to '/var/tmp/dropbear/dropbear_rsa_host_key'
Generating key, this may take a while...
[ util_execSystem ] 135: oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/zebra.conf"

[ util_execSystem ] 135: prepareDropbear cmd is "dropbearkey -t dss -f /var/tmp/dropbear/dropbear_dss_host_key"

Will output 1024 bit dss secret key to '/var/tmp/dropbear/dropbear_dss_host_key'
Generating key, this may take a while...
[ util_execSystem ] 135: oal_rip_updateConfig cmd is "rm -f /var/tmp/dconf/ripd.conf"

[ util_execSystem ] 135: removeAllRIPIpTableRule cmd is "iptables -L INPUT -v --line-numbers > /var/iptable"

[ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
[ util_execSystem ] 135: controlRipProcess cmd is "zebra -d -f /var/tmp/dconf/zebra.conf"

[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
[ util_execSystem ] 135: oal_ipt_fwDdos cmd is "iptables -D FORWARD -j FIREWALL_DDOS
"

iptables: No chain/target/match by that name.
[ util_execSystem ] 135: oal_ipt_forbidLanPing cmd is "iptables -t filter -D INPUT -i br+ -p icmp --icmp-type echo-request -j DROP
iptables -t filter -D FORWARD -i br+ -p icmp --icmp-type echo-request -j DROP
"

iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_ddos_delPingRule cmd is "iptables -t filter -D INPUT ! -i br+ -p icmp --icmp-type echo-request -j ACCEPT
"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_ipt_setDDoSRules cmd is "iptables -F FIREWALL_DDOS"

[ util_execSystem ] 135: ddos_clearAll cmd is "rm -f /var/tmp/dosHost"

[ util_execSystem ] 135: oal_initFirewallObj cmd is "ebtables -N FIREWALL"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -F"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -X"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P INPUT ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P FORWARD DROP"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -P OUTPUT ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -N FIREWALL"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -N FWRULE"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -i lo -p ALL -j ACCEPT -m comment --comment "loop back""

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -i br+ -p tcp --dport 23 -j ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -p tcp --dport 23 -j DROP"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -i br+ -p icmpv6 --icmpv6-type echo-request -j ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A INPUT -p icmpv6 --icmpv6-type echo-request -j DROP"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -i br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -o br+ -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT"

[ util_execSystem ] 135: oal_initIp6FirewallObj cmd is "ip6tables -A FORWARD -j FIREWALL"

[ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -D FIREWALL -j ACCEPT"

ip6tables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -F FIREWALL"

[ util_execSystem ] 135: oal_fw6_setFwEnabeld cmd is "ip6tables -A FIREWALL -j ACCEPT"

[ rsl_setStorageServiceObj ] 1024: mountFlag is 3,We start usb server

[ util_execSystem ] 135: oal_killDlnaMediaSeverProcess cmd is "killall ushare"

killall: ushare: no process killed
[ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

[ util_execSystem ] 135: oal_sys_unsetTZ cmd is "echo "" > /etc/TZ"

uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
Benjamin Zores (C) 2005-2007, for GeeXboX Team.
See http://ushare.geexbox.org/ for updates.
[ util_execSystem ] 135: oal_ipt_setWanPort cmd is "iptables -t filter -D INPUT -p tcp --dport 21 -j ACCEPT"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_ipt_setWanPort cmd is "iptables -t nat -D PREROUTING -p tcp --dport 21 -j ACCEPT"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_startPrintSrv cmd is "insmod /lib/modules/GPL_NetUSB.ko"

kcg 333 :GPL NetUSB up!
[ util_execSystem ] 135: oal_startPrintSrv cmd is "insmod /lib/modules/NetUSB.ko"

kc 90 : run_telnetDBGDServer start
kc 227 : init_DebugD end
INFO186B: NetUSB 1.02.61, 00020624 : Dec 16 2014 15:38:41
INFO186D: 7437: Archer C20 :Archer C20
INFO186E: AUTH ISOC
INFO186F: MOVE_HEAD filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO18C7: Reset device when disconnect
INFO0145: init proc : PAGE_SIZE 4096
INFO1740: infomap c11f0c74
INFO1743: sleep to wait br0 to wake up
INFO02CE: use dev Name br0
INFO174C: sleep to wait br0 end.
INFO1765: UDP_BROAD 7437 tcpPort:20005
INFO02CE: use dev Name br0
[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_ftp.ko"

INFO161F: tcpConnector() started...
[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_ftp.ko"

[ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 500 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_pptp.ko"

[ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p tcp --dport 1723 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: oal_openAlg cmd is "iptables -D FORWARD_VPN_PASSTHROUGH -p udp --dport 1701 -j DROP"

iptables: Bad rule (does a matching rule exist in that chain?).
[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_tftp.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_tftp.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_h323.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_h323.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_sip.ko"

INFO14F8: Bind to br0
[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_sip.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_rtsp.ko"

[ util_execSystem ] 135: setupModules cmd is "insmod /lib/modules/kmdir/kernel/net/ipv4/netfilter/nf_nat_rtsp.ko"

nf_nat_rtsp v0.6.21 loading
[ util_execSystem ] 135: oal_wan_HWNat_enable cmd is "insmod /lib/modules/kmdir/kernel/net/nat/hw_nat/hw_nat.ko"

Ralink HW NAT Module Enabled
[ util_execSystem ] 135: prepareDropbear cmd is "dropbear -p 22 -r /var/tmp/dropbear/dropbear_rsa_host_key -d /var/tmp/dropbear/dropbear_dss_host_key -A /var/tmp/dropbear/dropbearpwd"

.
spiflash_ioctl_erase, erase to 0x007c0000 length 0x85a9, nerase done
spiflash_ioctl_write, Write to 0x007c0000 length 0x85a9, ret 0, retlen 0x85a9

vovan26
OpenWrt разработчик
OpenWrt разработчик
Сообщения: 2451
Зарегистрирован: 12 мар 2014, 17:20
Страна: Узбкистан
Откуда: Узбекистан

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение vovan26 » 24 июл 2017, 16:53

А кто вам сказал вырезать юбут? Я вам говорил о заголовке, первые 512 байт.
Но и это не пойдет, я вчера посмотрел железо С20 и С50, у них разные чипы радимодуля 5ГГц. При загрузке роутер запускает вафлю и не может, т.к. драйвер для MT7610E (С20) не подходит для MT7612E (С50) и роутер уходит в постоянный ребут. Операция с ОФ файлом с юбут тоже не пройдет!
Разработка ПО для роутеров на базе OpenWrt.
Желание получить ответ, предполагает умение сформулировать вопрос. (И.В. Сталин)
На общие вопросы в личке не отвечаю, задайте его на форуме.

NeonClub
Сообщения: 10
Зарегистрирован: 21 июл 2017, 13:06
Страна: Latvian

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение NeonClub » 24 июл 2017, 17:39

vovan26 писал(а):А кто вам сказал вырезать юбут? Я вам говорил о заголовке, первые 512 байт.
Но и это не пойдет, я вчера посмотрел железо С20 и С50, у них разные чипы радимодуля 5ГГц. При загрузке роутер запускает вафлю и не может, т.к. драйвер для MT7610E (С20) не подходит для MT7612E (С50) и роутер уходит в постоянный ребут. Операция с ОФ файлом с юбут тоже не пройдет!
говорюж отпечатка у вас была . вместо баик . килобайт ) вот и подумал что так много то )))

Я так понимаю надо теперь мак адреса восстанавливать !
Вот токо как определить где в нех найти . пока не разобрался...

vovan26
OpenWrt разработчик
OpenWrt разработчик
Сообщения: 2451
Зарегистрирован: 12 мар 2014, 17:20
Страна: Узбкистан
Откуда: Узбекистан

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение vovan26 » 24 июл 2017, 17:57

Роутер все равно не заведется, надо брать раздел радио из "убитого" дампа или искать родной дамп.
Или нести в авторизованный СЦ.
МАС: 007df100 - 007df105
Разработка ПО для роутеров на базе OpenWrt.
Желание получить ответ, предполагает умение сформулировать вопрос. (И.В. Сталин)
На общие вопросы в личке не отвечаю, задайте его на форуме.

NeonClub
Сообщения: 10
Зарегистрирован: 21 июл 2017, 13:06
Страна: Latvian

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение NeonClub » 24 июл 2017, 18:30

vovan26 писал(а):Роутер все равно не заведется, надо брать раздел радио из "убитого" дампа или искать родной дамп.
Или нести в авторизованный СЦ.
МАС: 007df100 - 007df105
Проще уш тогда купить такойже роутер и слить дамп ...
Ибо дорога обходится почти в стоимость роутера ...
написал на 2 форумах , может кто и поделится ...

Работать та он работает после вырезания 512баит .. но без влана )))
Может быть есть возможность запустить опенврт ?
интересует 5гхз . 2.4 можно и через усб на опенврт запустить ...

существует роутер в мире C20i .. интересно какие сходства у них есть ...

vovan26
OpenWrt разработчик
OpenWrt разработчик
Сообщения: 2451
Зарегистрирован: 12 мар 2014, 17:20
Страна: Узбкистан
Откуда: Узбекистан

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение vovan26 » 24 июл 2017, 18:38

Вабер или imo есть? Кинь в личку.
Разработка ПО для роутеров на базе OpenWrt.
Желание получить ответ, предполагает умение сформулировать вопрос. (И.В. Сталин)
На общие вопросы в личке не отвечаю, задайте его на форуме.

vovan26
OpenWrt разработчик
OpenWrt разработчик
Сообщения: 2451
Зарегистрирован: 12 мар 2014, 17:20
Страна: Узбкистан
Откуда: Узбекистан

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение vovan26 » 24 июл 2017, 18:47

Разработка ПО для роутеров на базе OpenWrt.
Желание получить ответ, предполагает умение сформулировать вопрос. (И.В. Сталин)
На общие вопросы в личке не отвечаю, задайте его на форуме.

NeonClub
Сообщения: 10
Зарегистрирован: 21 июл 2017, 13:06
Страна: Latvian

Re: После прошивки Beta версии роутер превратился в кирпич.

Сообщение NeonClub » 25 июл 2017, 00:17

Роутер воскресил , поделились дампом тут
https://forum.lede-project.org/t/need-d ... c20v1/5264

Ответить

Вернуться в «Archer C20»